4.9 from 763 reviews

26 San Diego neighbourhoods

$89 service call, waived with the repair

(760) 330-4020
Whirled Service Appliance repair · San Diego (760) 330-4020

A maker we work on

Electrolux Appliance Repair in San Diego

Electrolux is the parent of Frigidaire and sits above it on specification, with many of the same pumps, motors and elements underneath a better cabinet. That makes it one of the easier premium-looking brands to repair, because the components that fail are shared with a mainstream line and are stocked locally.

What Electrolux builds

Front-load laundry is the core product, usually the washer and dryer pair on pedestals, along with French-door and counter-depth refrigerators, built-in dishwashers, wall ovens and induction cooktops. The laundry pairs use a conventional belt-driven drum and a pump filter behind the lower panel, and the dishwashers follow European practice with a filter stack rather than a grinder. Across the range the failures are ordinary ones, and the plate inside the door frame decides the part.

What we are called about

Washer will not drain

The pump filter behind the lower panel collects coins, lint and hair, and the machine posts a drain fault while the pump itself is still healthy. The impeller gets checked with the filter, and the hose loop under the sink is worth a look before anything is replaced.

Door lock not releasing

The lock holds the door and confirms it to the control, and its switch wears out with use. The result is a machine that refuses to start, or one that finishes and keeps the load shut inside. The manual release behind the lower panel opens it; the assembly is still the repair.

Dryer running cool

The heating element or a thermal limiter on electric models, the igniter or the coils on gas. A tripped limiter is a symptom of restricted airflow rather than a fault in itself, so the duct and the lint housing are cleared first; fitting the part alone returns the same failure.

Refrigerator ice maker jamming

The fill valve, a frozen fill tube and the module cover most of it, and the door seal matters because warm air reaching the compartment refreezes the cubes into a block. This is the same design family as Frigidaire, so the parts and the fixes carry over.

Electrolux repairs by appliance

Reviews

What people wrote afterwards

5 from 613 reviews

  • ★★★★★

    Rental unit. The dryer shut off hot part way through and would not restart until it cooled. The high-limit thermostat was cycling because the outside vent flap had jammed shut. Cleared, and a new thermostat fitted.

    Kwame S.Pacific Beach

  • ★★★★★

    It would start and stop repeatedly on its own. He checked the door switch, which went intermittent whenever the door flexed, and replaced it. He also pointed out the vent hose kinked behind the machine.

    Josephine D.Serra Mesa

  • ★★★★★

    Fan noise rose and fell all evening and the fridge went warm. Ice had built up around the evaporator fan blade so it was striking the shroud. He melted it out and sorted the door seal letting warm air in.

    Ephraim D.San Carlos

  • ★★★★★

    The plate turned but nothing ever got warm. Its magnetron had failed. He explained why guessing at that part is a bad idea, tested the high voltage side properly, and only then fitted the replacement.

    Estelle J.La Jolla

  • ★★★★★

    Its fan kept running long after the door was open and nothing would stop it. A relay on the control board had stuck closed. He fitted a new board and made sure the vent damper above was moving freely.

    Aleksandr H.Mission Valley

  • ★★★★★

    The door had dropped and stopped sealing, so everything came out cooked unevenly. Both hinges were bent. He replaced the pair, reset the door alignment, and put a new door gasket on while he was at it.

    Nikolai T.Bay Park

Answers

Electrolux questions

Is Electrolux the same as Frigidaire?

Same company, and a lot of shared engineering, with Electrolux positioned above Frigidaire on finish and features. For a repair that is useful: pumps, motors, elements and locks cross between the two, so parts are easy to source and the diagnosis on one applies to the other.

Why does my Electrolux washer stop with water in it?

Nearly always the pump filter behind the lower panel rather than a failed pump. It collects coins, hair and lint until the machine cannot empty within its allowed window, and the control then posts a drain fault. The impeller gets checked at the same time as the filter.

Are Electrolux parts easy to get here?

Yes for the shared mechanical components, because they are used across the Frigidaire range as well. Control boards and trim specific to a single Electrolux model year take longer, and those are ordered against the plate inside the door frame rather than the model on the receipt.

Is an Electrolux front-loader worth repairing?

For pumps, locks, elements, hoses and even bearings, yes, and the cabinet outlasts all of them comfortably. It stops making sense once the wash assembly itself has gone, because the drum, the spider and the bearing then come as one long job rather than three small ones.

Get it looked at

Have the Electrolux model number to hand

The make, what the machine is doing, and how it is fitted — stacked in a closet or standing in a garage. That is usually enough to know what the visit involves.

(760) 330-4020 Book online

$89 service call, waived when the repair is approved.