4.9 from 763 reviews

26 San Diego neighbourhoods

$89 service call, waived with the repair

(760) 330-4020
Whirled Service Appliance repair · San Diego (760) 330-4020

A maker we work on

Smeg Appliance Repair in San Diego

Smeg is an Italian maker best known in this county for the FAB refrigerators, the rounded retro units in strong colours. They are conventional single-system refrigerators underneath a distinctive shell, which makes the diagnosis straightforward and the parts a matter of ordering rather than searching.

What Smeg builds

The FAB refrigerators are the recognisable product, and most of the ones here are a second machine or a kitchen statement piece rather than the main cold storage. Smeg also sells Portofino and Victoria ranges, built-in ovens, and freestanding and integrated dishwashers, all built to European conventions: compact cavities, condensation drying on the dishwashers, and controls that report faults sparingly. Parts come through the importer against the model plate, so identifying the exact variant matters more than on a mainstream brand.

What we are called about

FAB refrigerator running warm

The thermostat or the door seal before anything else. These are single-system refrigerators with a small cabinet, so a gasket that has hardened, or a door that no longer pulls itself shut, shows up as a warm cabinet quickly, particularly in a kitchen that gets afternoon sun.

Door dropping on a FAB

The doors are heavy for the size of the cabinet and the hinge takes that load every time. Once it wears the door sits low, the seal loses contact along the top and condensation or frost follows. The hinge and the gasket usually get replaced together.

Oven not holding temperature

The temperature sensor or the thermostat, and on the gas models the safety valve. Smeg cavities are compact and heat quickly, so an oven that overshoots and then swings low is more often a sensor problem than an element one.

Dishwasher not draining

The filter, the drain pump and the check valve, in the European layout with no food grinder. Anything that gets past the filter arrives at the pump intact, so a label or a fruit stone is a frequent find and the pump itself is often undamaged.

Smeg repairs by appliance

Reviews

What people wrote afterwards

4.9 from 600 reviews

  • ★★★★★

    The door had dropped and stopped sealing, so everything came out cooked unevenly. Both hinges were bent. He replaced the pair, reset the door alignment, and put a new door gasket on while he was at it.

    Nikolai T.Bay Park

  • ★★★★★

    There was arcing inside and a burnt smell every time we used it. The waveguide cover had charred right through. He replaced the cover, cleaned the cavity out, and checked there was no damage behind it.

    Corinne D.Pacific Beach

  • ★★★★★

    Older house with the laundry off the back porch, and the washer would not start at all. The timer knob had lost its splines so the shaft just spun free. He fitted a replacement and tested every cycle position.

    Wendell J.Coronado

  • ★★★★★

    Gas dryer stopped heating entirely. He checked the igniter, which was glowing but never lighting, and traced it to a failed gas valve coil. Both coils were replaced as a pair and it fired first time afterwards.

    Emmett R.Point Loma

  • ★★★★★

    It would drain but never spin, so every load came out dripping wet. He checked the door interlock first, then found the belt had jumped its pulley and stretched. A new belt went on and the tension was set properly.

    Loretta F.Clairemont

  • ★★★★★

    Mid-rise building with in-unit laundry, and mine had stopped mid-wash with the door sealed. The main control board was dead. He confirmed that with a meter instead of guessing, ordered the part, and came back to fit it.

    Meredith Q.Bankers Hill

Answers

Smeg questions

Are Smeg parts available in San Diego?

Through the importer rather than off a local shelf, so most repairs involve an order placed against the model plate. Seals, thermostats and hinges for current FAB models are generally straightforward. Coloured trim and cabinet panels are the parts that take the longest to arrive.

Why does my FAB fridge sweat around the door?

Condensation on or around the seal usually means the gasket is no longer making even contact, often because the hinge has worn or the door shelves are heavily loaded. The cabinet is small, so the difference between a good seal and a tired one shows up quickly.

Is a FAB refrigerator a real refrigerator or a design piece?

Both, and it matters for expectations. It is a conventional single-system unit with a small freezer compartment inside a heavy retro shell. It cools well for its size, but it is not equivalent to a full-size French-door machine and it struggles when asked to do that job.

Do you work on Smeg ranges and dishwashers as well?

Yes. The dishwashers follow European practice, with a filter stack instead of a grinder and condensation drying, which makes them predictable to diagnose. The ranges are conventional gas and electric underneath, with the thermostat and the ignition covering most of what goes wrong.

Get it looked at

Have the Smeg model number to hand

The make, what the machine is doing, and how it is fitted — stacked in a closet or standing in a garage. That is usually enough to know what the visit involves.

(760) 330-4020 Book online

$89 service call, waived when the repair is approved.